M C O M

Shop Details

Categories

MCOM WLCD

Model: MCOM WLCD

Name: -

Category: Gsm Based Pump Starter And Water Level Controller

Discription:

MCOMWLCD based water level indicator is equipped with best quality material & latest technology. It shows 3 levels of tank (Full, ½, 10%) through high glow LED lights. We use long life molded sensors built with high grade stainless steel.

The indicator is specifically designed to use where water is taken from any regular source of water like earth water or irregular source like corporation pipeline. These are available in different specifications to meet the requirements of Our Clients.

Generally, especially during summers, water is supplied at very odd hours of the day or for a very small period of time. Normally, you will have to be available at that time to switch on the motor. Then keep in mind, whether the tank would have been full or not and after all these, still you are not sure whether the tank is full or not. MCOM Automatic water level controller once installed, system automatically takes care of your motor / pump and thus you need not worry about, whether water is there in the tank or not.

Get A Quote


·        Programmable Timer

·         Float Switch Sensors / No Scaling on Sensor (Carbon Free)

We are best in after sale services also and our aim is to provide benchmark services in the industry. Our few beneficial points are mentioned below:

·         High Quality

·         Quick Service

·         Latest Technology

·         Customer Satisfaction

Specialty: We provide float switch sensors: no scaling/ depositing of any salt [carbon free] on the surface of sensors, even after years.

 

The Concept of Water Level Controller System:

 

The Water Level Controller System is an Electronic Equipment which when electrically connected to the starter of any given pump set motor will control the operation of the pump set depending upon the water level in the Source and Destination Storage Tank.AdvancedAutomatic “WATER LEVEL CONTROLLER” unit Manufactured by “MODERN COMMUNICATION TECHNOLOGY “. This system when electrically connected to an Pumpset starter, performsthe following functions automatically:



  • Switches ON the Pumpset when Water level drops below pre-set level (i.e. T2 level) in Overhead Tank.
  • Switches OFF the Pumpset when Water level in Overhead Tank becomes full (i.e. T1 level).
  • Switches OFF the Pump set when Water level is low in Sump/Well/Borewell (i.e. S2 level).
  • Switches ON the Pump set when there is sufficient water in the Sump/ Well / Bore well (i.e. S1 level).
  • Switches OFF the Pump set when there is a Dry run (i.e. when Water is not being pumped into Overhead Tank due to any reason).
  • All these functions are automatically performed. Manual interference is absolutely not required.
  • Manual operation is also possible if and when required by operating the switch in Manual position.


Specifications

 Input Voltage (AC)     : 220 – 270 VAC, 50 Hz

On voltage (Cold Start): 250 VAC

Pump Current Range    : 5 Amp.

 Resetting mode          : Manual by OFF switch.

 Output Relay Contact

 Relay Mechanical life            : 10 lac operations

 Dielectric Strength     : 2.2 KV, 50 Hz for 1 min

 Enclosure & Mounting

 Enclosure Material     : ABS Enclosure

• Mounting      : Wall Mounting with 4 screw M4 × 15 mm

• Temperature  : 5 to 60°C

• Humidity      : Up to 90% RH

 

9. Dimensions & Weight

• L × W × D (mm)      : 70 x 100 x 45 mm

• Power Consumption : Less than 1 Watts

• Weights        : 450 gms.

Applications

Industrial

Domestic

Connection Diagram

 

INPUT 230 VOLT

PUMP START

PUMP STOP

SIX LEVEL SENSORS

TWO WIRE FOR LINE AND NEUTRAL SUPPLY, RED FOR LINE, BLACK FOR NEUTRAL

TWO GREEN WIRE

TWO BLACK WIRE

THREE SENSORS FOR OVERHEAD TANK AND THREE FOR LOWER TANK, TWO-TWO WHITEWIRE FOR EACH SENSOR.

Related Products

Send Request Now

And we'll get back to you within 48 hours.

Model: MCOM WLCD

Name: -

Category: Gsm Based Pump Starter And Water Level Controller

Send Request